I'd be happy to help, but really cant read the drawing. I gather what you really have is more of a walk way to a space than a walk in closet. The walkway is not wide enough for anything but some hooks on the wall and even then I'd keep them above shoulder height or you'll catch you and your clothes on them as you pass. The real storage opportunity is at the end where you need to maximise the depth for hanging space. Either make it all double hanging (double tier with a shelf at 2100m high and a rod and shelf at 1050mm high. running it into the nib will give you a total of 30000mm with the 380 return and the 1200 back wall. If you need dress length, take as little a you need then the remainder in double hanging Tip;.If you only have a coupleof full length items you could eliminate full hanging and just use robe hooks on the walk way. You could also use the walk way for hooks for belts, ties etc. If you put anything anywhere else you wont be able to find anything, so I'd keep it at that. Of course you would get a shelf over the double hanging at 2100 high. Also avoid any low storage becuase you cant bend over in spaces like these. I've done a rough sketch for you, but it doesn't seem to want to load :)

Hi Bec. I have a Federation home with high ceilings and I just installed a built-in robe in my master bedroom. The door swing lands within the wall-to-wall run. My solution was to install a 2200mm high robe and run a decorative capping all the way round to top edge. Behind the door, I stepped the robe back and installed a wide stack of drawers and open shelves. It neatly fits in behind the swing of the door without needing expensive structural modifications. I don't recommend going all the way to the ceiling where you have the luxury of height. It will shorten the room and you'll never get up there. In my case, the capping provides a lip which helps to conceal things I store up there that I don't use often like suitcases and bedspreads.

There are a number of challenges here that arise frequently, namely: The space is tight, and budget seems an issue. Door options: 1 sliding cavity door into robe- problem: people rarely bother to close them so often a pointless result 2 Hinged doors on the cabinetry-problem the galley you have is only 2000mm wide or even 2200mm. This will make it very tight if you plan to have hinged doors with both sides at 600mm carcass depth leaving either 800mm or 1000mm aisle. This will mean you don't have clearance for you and a door swing, assuming a door width of 500-600mm . You will find it very claustrophobic, and impossible with two people using it. 3 Sliding doors-these will limit your access to the interior and most people dislike them, however probably a workable solution- if you go this way, put the door track at 660mm not 600mm to clear suit jackets. 4 Enclose only one side of the wardrobe with doors and have the other for hanging which tend to be neater than the shelf items.(choose the side that is most visible from the front door. Depending on your ratio requirement of hanging to shelving/drawers, you might fit all hanging on one side then you can have drawers all along the lower section with shelving above with upper doors only. That way, the swing of the doors is easier as you don't need to clear your feet, only your upper body. Then gain bonus space in the area by making the enclosed cabinets only 400mm deep externally. Folded clothing folds to 360-380mm so don't waste the space with 600mm depth. Any additional hanging required on the enclosed wall is positioned distant to the entry and will be mainly out of view. This will save on doors, space and look tidy. It requires a custom build, the cost of this walk in robe in gloss melamine was around $7500.00 including design. Best of luck. The walk in below is 2000mm across, the first section on the left is 400mm deep for his shoes and drawers, the section on the right is 620mm deep. The distant section on the left is 600m providing space for hanging. That way the aisle in the first part is more generous and this tight space feels generouson the left we have his shoes behind doors and drawers below-at 400mm deep this makes the aisle more generous to cope with doors the photo below shows with door near the entry to conceal the"mess"from the walk way(see the appearance from the doorway in top photo), the hanging at the end is not visible at the entry we made the most of the full depth for shoes in our custom drawers

Hello. I'm doing renovation whole apartment and also built in wardrobe (hinged door) for two room. We had argue about the internal drawer size for each wardrobe. One wardrobe cabinet internal size is w 1117 x d 600 and second is w 1063 x 510 The builder brought the internal drawers way too smaller than actual size of cabinet. he says that it is how usually doing for hinged door wardrobe. so actual internal size of wardrobe is w 1117 x d 600. the drawer size is 900 x 300. Another wardrobe is w 1063 x 510 and brought 850 x 330 drawers. ( this is all bottom drawers) The problem is that the inside drawer is too small and has a big handle like kitchen drawer. The wardrobe drawer should have no handle as it is inside of wardrobe and need to bigger and fit into actual space of cabinet. The depth of drawer is only half way of actual size of cabinet depth. the width size also about 5 to 12 cm is empty gab between actual wardrobe panels. It is nearly half of actual cabinet space is just empty. Finally the builder admit that the depth size made wrongly as there is about 30 cm empty gab but not the width size so they want to make a deeper drawer but keep width between panel about 5 to 10 cm. The builder says rest space will cover up by the panel and also keep arguing that the drawer is small because they need to give a space for door hinge because this one need to install next to drawers. Door hinge is only 2 cm wide and 2cm depth. I do understand door hinge but still too many space is empty. Therefore, I have asked him to make a drawer for right size of cabinet (make drawer size wider and deeper) and put the door hinge between drawer. But the builder refuse to make new one as they need to make whole new drawers and says that it is standard to keep space between 5 to 10 cm between door, panel and drawer all around and cannot compare with other brand such as ikea or freedom. Simply they said they cannot do it. Also, he argues that I should request make drawer to be back to back size before making. I request standard drawers and sent him the pictures before making like https://www.instagram.com/p/B-MRD7XlUfi/. Total 16 drawers was made wrong size. every drawer has different size gabs. My question is that is true to have gab between 5 to 10 cm between drawers and actual size of cabinet due to door hinge? This should be the custom built in wardrobe.