Hi Brett, first off - well done for reaching out (without ego) and asking those that know and those that have tried and found results. If you are going with the brick veneer, the cavity is key to your moisture and thermal capabilities, after years within the house. Gyproc is not designed for anything but a 'skin'. If you increase thermal layer on the walls by asking he outer layer of the stud work with good quality silver sarking or Tyvek. Tape joints to eliminate vapour transfer to internal gyproc. Use 12.5mm gyproc on all external walls. OR Use 12.5 silver backed gyproc board on walls instead of previous. If coast effective -I would use this on the ceilings also. Principle being - isolate the internal breathing environment both thermally and other from the externals. Then deal with any ventilation or thermal issue by themselves internally. Look at why a house is designed, then go 100% better. The problem with roof voids is cold at night and heat in day, focus on high air barrier and high 'R' values here. Internally, consider + and -, as in, where it is cold-draw heat to it (South+ low) where it is hot, draw coolth to it (North & high). The result will be both continuos balance or equilibrium in comfort, thermally, energy and ventilation wise... Hope this helps : )

Hi Chris Just following up your request for further info between double glazing and/ or filming single glazing Etc Your more than welcome to call me direct here in Tassy for a more detailed info. that’s not possible via this comments section . But just to highlight a few things for all interested readers . Firstly , it’s important to understand the “ Technical” differences between both single & double glazing ( particularly the different types of additives/ manufacturing processes etc that’s goes into making glass that can make a difference to how they perform technically and the ability to do what you want it to do and then theirs the choice of aftermarket window films . Whether the choice of an aftermarket window film application is considered to either single or double glazing to solve one or more problems, one must understand the pros and cons as to the window film manufacturers guide lines and their recommendations as to what type of film should be used or avoided considering the different window components and the different types of glass that goes into making the final window product . Secondly ; and equally important ; one must understand the differences between radiant heat and convection heat . Unless the glass is specially treated at the glass manufacturers or has an added solar film coating applied ( such as suitable window film ) when compared to clear glass and whether as a single glazed or a double glazed unit ; will NOT stop all the direct RADIANT heat through the glazing . Double glazing , or even triple glazing , works on the same principle like a thermos flask ; to reduce / slow down the transfer of CONVECTION currents ( hot or cold air temperatures ) from one side to the other . Radiant heat and convection heat are two different things and requires different ways to solve the problems . Double glazing is designed to reduce “convection” air temperature from moving from one side to the other , of the window . Other additional manufacturing processes can improve both insulation and heat reduction abilities . You mentioned a ceramic film and the infra red ( heat component ) reduction. I was wondering why a ceramic film was mentioned compared to say either a semi or fully reflective film choice !!!! Don’t get confused with all the advertising thats on offer via sales reps pushing their product as being better than other film options unless you fully understand both the advantages and disadvantages. One must compare apples with apples when comparing any technical data as many companies don’t all stick to a common standard tech specs making it difficult for customers to compare and often confused . The two main considerations when choosing a film ; particularly when double glazing is installed ; is the :- total solar energy reduction ( SER) and secondly the amount of absorption of heat ( SEA ) into the glazing . These are the two main factors I look at when heat transmission is a problem for a customer . The SER is the amount of the overall reflected away from the glazing and the SEA is the amount that’s is absorbed into glazing ( glass ) as this will effect how much increase in the overall temperature of the glass Particularly the panel which is tinted in a double glazing application which is normally the room side . The main problem if the glass temperature increases , it will increase the chance of glass breaking due to thermal stress .( gets too hot it will eventually break ) . One also has to take into account the quality of the glass , particularly most being made in Asia now .where quality may be an issue compared to Australian made glass .!!! Basically You need high SER with the lower SEA as an ideal choice . From my experience with over 40 years in the window tinting industry here in Tasmania that the fully reflective film I often use ; particularly on double glazing ; is a number one choice ; then secondly the less reflective MEP films neutral based film either in the suggested medium grade as generally the two films the manufacturers suggest in their guide lines As single glazing goes , between the full reflective or secondly the darker neutral ( a cross between the medium neutral and full reflective films ) I’d be interested in see the data on the ceramic film choice for me to compare to out of interest . The three films I’ve mention are by no means the only choices but many other factors comes into play that need to be taken into consideration . Much more on the subject but hope this may offer some interest to discuss further . Protek window tinting & blinds (Tas)

Clau2000 our manufacturer was in Melbourne, supplier in Canberra. Despite being happy with the product we really struggled with the level of service from the supplier. Quite frankly the business owner was rude, uncommunicative and very difficult to deal with and I would hesitate to recommend her business to anyone. At one point we contacted the manufacturer but he insisted we had to go through his ACT supplier and could not order directly from him (either us or our builder). Our first set of windows were installed on a westerly facing wall & get direct sunlight for the hottest part of the summer afternoon, they have been installed for 4 years and are showing no sign of deterioration. We went with E10 glass, double glazed and they do an amazing job of blocking the summer heat.

HU - I really think you should start a new thread on this issue as, many people may not see this when it is an old thread. I've had different colours of the exact same carpet in a house, but there were rooms in between so it was never obvious, but two different carpets together is another thing again. How did you feel the green looked with the off white?? If you were happy with the two colours together, then you could put any colour you liked with it, otherwise maybe remove the carpet from the stairs, although that can then make the stairs very noisy. What is the condition of the off white carpet - do you feel it may need replacing soon so you could match whatever you do now, if it is a carpet that does not look like being discontinued in the near future. You may even be able to match the off white that is there. Another hassle with using two different carpets is the weave and texture can make them look more odd together than different colours. It is really hard to advise you on this, you really need to see the two carpets together, at least it is easy to bring home carpet samples to see just what you can live with. Good luck.