Firstly...are you sure they are jarrah and not som other more exotic timber? If you are fortunate enough to have a genuine 1932 built cottage I say "Don't Do it!" Just look at the beautiful timber in that floor! It would be sinful to paint it. I have a 1924 cottage with beautiful hoop pine floorboards all from the day it was built. My suggestion is to have the boards sanded and polished. I would not even dare go near them with polyurethane. I have turned back the clock and used the methods of the period of the house...a mix of pale boiled linseed oil and kero. Put it on with a mop or a deck mop or a wool mop leave it soak in. Re-do and leave it soak in,,,( you won't get patches...the floors will just soak it up.) Third coat, add a bit of turps to the mix as a white ant deterrent. Then, when the floors look like they've soaked up enough, get a big old fashioned string mop...if you can find one...or use a deck scrubber and old towels...or even a wad of new ones...100% cotton...its worth it, and rub off as much of the surplus as possible...wear sox so you will notice when the sox do not get oil stained anymore. First go is a long process but you will be really pleased when the floors have had several "drinks". After that you could get just an ordinary floor varnish or oil or just a sealant. Some of the modern wood treatments are really good. Then, every so often do the boards over with your "Oil Mop". You will never find timber like that again and, in my experience, it adds to the value of the house big time. Do what you like to any gyprock and plastered walls but PLEASE love your floorboards and any natural timber...especially from that era. I've been in this old cottage for 32 years. Everyone wants to know where I sourced the "new" floorboards", and who did I get to make my silky oak windows! Hope that helps.

Second attempt was with Windex and same paper towel, which cleaned the two honed surfaces up pretty well. The lighter Raw Concrete seems to have been easier than the Sleek Concrete. And finally, to get rid of that pot scratch I used a non-scratching Scotch brite pad (what we usually use on dishes) with some diluted Soft Scrub. This one took a little more elbow grease but I'm satisfied with the results. My opinion is that comparing the two surfaces (honed vs. glossy) there is a marked difference. That being said, I currently have tile from 1978 and grout lines that are so deep and narrow I have to scrub them out with a toothbrush. I guess it's all a matter of perspective. We decided to go with the Raw Concrete after all, and like others have said, just expect that it'll take a little more work and show a few more stains. But then again, isn't that the whole point of concrete? That it looks industrial? I hope this has helped someone. If anyone is interested I'll try to post some more photos and real life feedback in a couple of weeks once ours is installed.

Sounds like a very stressful situation! If there is absolutely no way the builder will allow you to change things (even if they did, I imagine they would ask you to foot the entire bill of pulling the tiles down and replacing all water proofing in addition to new tiles), I can make a few suggestions for improvement. Firstly I would suggest replacing the tiles above the vanity with a white mosaic, a patterned or a textured feature tile/strip. You could also use this same tile to replace the vertical feature in the shower. There are some beautiful shapes and sizes available to choose from. Secondly I would address the grout situation in this way: Floor - dark colour grout & Walls - Light colour grout. Lastly if it does not prove too difficult or expensive, maybe replace the tiles below the vanity with a plain white tile (could be similar size). Good luck and I am sure once you have a lovely mirror up and some crisp white towels, it will look just wonderful.

Hi, Bronwyn - love your kitchen :) We are planning a complete kitchen renovation and love the two choices that you have for the cabinets fronts. Seeing you did your kitchen about 4 years ago my first question will be of durability :) How do both finishes feel - plasticky or more like real wood? For the Voxtorp I will have only wall cabinets (no drawers) of it and wonder with the integrated handle - does it align well (I tend to have OCD and if there are no even will drive me crazy :) ). Thanks :)