Well after a very (very very very) long time my Living Room is all but complete. There is some work to do behind the new steps and some trim to be put on the bookshelves. A light is to be put between the couches (that the electrical cable hanging down) and the wall lights are going to be removed. So just a quick rundown on what has been achieved; Two sky windows - Velux - roofing guy Sheeted under the beams - plasterer New carpet – Bunnings – carpet layer Closed off the old bar and put in a door – builder and plasterer Installed ceiling fans – Hunter, remote control, reversible – electrician Installed downlights - electrician Painted the endwalls – Solver Paint but Dulux Chine White colour - me Painted the ceiling – 2 x coats Solver Ceiling White over 2 x coats plaster board sealer - me New blinds (venetians) and curtains - from Spotlight - me Installed a gas bayonet heater (until I can afford a gas ‘wood’ fire for the fireplace – cripes they are expensive) – secondhand from Garage Sale - me Installed bookshelves – 2 x 202mm high + 2 x 106mm high Billy Bookshelf and 2 x Brimnes Cabinet - me Built and installed new steps and bench top on bookshelf – laminated Beech bench top, cut to size and routed, stained and oiled - me Sofas – Ikea Ektorp - me So some things I would have done differently. The downlights would be warm white not welding mask white. In fact I would re-think the whole light thing and possibly use lights with reflectors that were dark so that light was only reflected down. They would ‘lower’ the ceiling and make the room cosier I think. I kinda like the ceiling fans but had seen some which were awesome but really expensive. Then I saw ones very similar to the awesome ones but much cheaper but by then it was too late. I should have put bi-fold doors where the old bar was instead of a swinging door. I suspect that it will be unlikely now that I can use the room for its intended purpose. In fact with hindsight I coulda shoulda done the job myself rather than getting a builder in. It’s not as good as it should be and that has disappointed me. The bookshelves have come a up a treat – need to finish them off though with some trim. All from ‘Ikea’ except for the timber bench top. The bench top was a light bulb moment and breaks up the all-white appearance of the shelves. Also the white of the shelves and the white of the cabinet were slightly different and the bench has helped disguise that. The bench top and the steps were laminated beech panels from ‘Bunnings’ that I had cut to size. I stained them, put a router over the edge to round it off and then coated with Tung Oil. The bookshelves look bigger in real life than they do in the photos too. So now to sit and enjoy my handy work.

I think you did a good job congratulations ive also tried spraying door handles and they go tacky as the paint does not adher to them even with esp or penetrol

Hello Northstar 1 thing to remember when choosing your lights .If you want the light down choose a down facing lampholder, dont drop them to low as the GLARE from the globes in your eyes every time they are on is annoying as, every lit pendant you showed had an incandescent globe so if your going to use Fluro globes they will look worse.LED globes with a cleeear glass would be best. Avoid carbon filament even though they look great its a low light output. Depending on your budget take a look at Mondoluce on line they have some amazing glass pendants from Italy and in multiple sizes.

Hi Paul, I hear your collective frustration! my comment about light bouncing into your eyes was in response to your question about bouncing light onto your faces from a light placed behind the vanity (from memory). Have you seen Dr Renos comment here - still the most logical response to me. https://www.houzz.com.au/discussions/5148857/where-to-place-power-points-and-lights#n=5 So I'm going to go for side lights next to the vanity cabinet. Trouble is, my vanity is off-centre to the cabinet mirror, so I still have to sort that one out. Time spent really considering this is well worth it. I think LED downlights may very well cast shadows, sorry to say :-) and the next consideration is what colour temperature - warm white or daylight? For relaxing ambience (75% bathroom function) it will def be 3000 warm white for me, however for the vanity functions it will be 4000K (daylight) so I will probably get the vanity lights switched separately to the main room light, maybe put that on a dimmer... I know there are some LED bulbs available that enable the colour temp to be changed within the same bulb...