A chippy can create any kind of decorative effect you desire (its just fibre board and mouldings) and you can vent the mechanical hood under it. I have a godawful stainless steel modern hood in my vintage cottage. I'm sure the last residents loved it, but they failed to actually have the hood vented properly. It just vents into the roofspace. So I now have the opportunity to remove the largely useless anyway hood and start over. I'm planning the same as you. A faux hearth, boxed in with fibre cement board and then with decorative mouldings attached. The actual mechanical part will be properly vented outside.

Hi Kruti. Those new pieces are lovely. There’s a houzz article in Stories about how to decorate a console table. If you select Stories, then Interior Design, then Decorating, and then type ‘how to decorate a console table,’ in the window, the article should pop up. I think you will find it very helpful.

There are a number of challenges here that arise frequently, namely: The space is tight, and budget seems an issue. Door options: 1 sliding cavity door into robe- problem: people rarely bother to close them so often a pointless result 2 Hinged doors on the cabinetry-problem the galley you have is only 2000mm wide or even 2200mm. This will make it very tight if you plan to have hinged doors with both sides at 600mm carcass depth leaving either 800mm or 1000mm aisle. This will mean you don't have clearance for you and a door swing, assuming a door width of 500-600mm . You will find it very claustrophobic, and impossible with two people using it. 3 Sliding doors-these will limit your access to the interior and most people dislike them, however probably a workable solution- if you go this way, put the door track at 660mm not 600mm to clear suit jackets. 4 Enclose only one side of the wardrobe with doors and have the other for hanging which tend to be neater than the shelf items.(choose the side that is most visible from the front door. Depending on your ratio requirement of hanging to shelving/drawers, you might fit all hanging on one side then you can have drawers all along the lower section with shelving above with upper doors only. That way, the swing of the doors is easier as you don't need to clear your feet, only your upper body. Then gain bonus space in the area by making the enclosed cabinets only 400mm deep externally. Folded clothing folds to 360-380mm so don't waste the space with 600mm depth. Any additional hanging required on the enclosed wall is positioned distant to the entry and will be mainly out of view. This will save on doors, space and look tidy. It requires a custom build, the cost of this walk in robe in gloss melamine was around $7500.00 including design. Best of luck. The walk in below is 2000mm across, the first section on the left is 400mm deep for his shoes and drawers, the section on the right is 620mm deep. The distant section on the left is 600m providing space for hanging. That way the aisle in the first part is more generous and this tight space feels generouson the left we have his shoes behind doors and drawers below-at 400mm deep this makes the aisle more generous to cope with doors the photo below shows with door near the entry to conceal the"mess"from the walk way(see the appearance from the doorway in top photo), the hanging at the end is not visible at the entry we made the most of the full depth for shoes in our custom drawers

Custom joinery is comparativley more expensive than the Ikea pre-fab options as you are paying somebody for the labour. You are also paying for their skills and experience to measure up correctly, to make it work with your crooked walls (no wall is ever straight and perfect), and to fit it exactly to the space it was designed for, without any crooked gaps that collect dust and spiderwebs. You also are paying for somebody to go back to if something sticks or jams, or doesn't work the way it was intended to. To make the cheaper options look neat and complete you do need good craftsmaship skills to install and work out how to get it straight and neat, but as it works on standard modules it never fits perfectly into the space, there are usually gaps. For instance their kitchen modules are designed around a 200mm module. If the kitchen space you have is 3300mm, then you need to figure out a way to cover the 100mm gap. With custom joinery it is designed to fit perfectly in the 3300mm space. If you can't assemble Ikea units perfectly you don't really have anywhere to go back to if you stuff it up. If you don't have these skills then you will need to employ somebody who does, and at the end of the day you may not save a fortune. Best of luck, Dr Retro of Dr Retro House Calls