yep, stunning. I been drawing something similar for a while and it's awesome to see your ab fab results after your OP. I got interested in some ikea solid timber benchtops, not nearly as nice as yours, and thought I'd combo them with black cabinets, white stone and white walls (just a "what if" design). so I totally love your kitchen. it's great how well the tiles look now compared to when you first posted, they really excite me! and the lightshades against the black wall. and what's that dining area I see? that smoked glass table top with timber trestles and black chairs and that black and white rug? where you get those?! I want to see more! congratulations, it's hard not to gush! big ups to Mldesign too.

Anyone who has the luxury of an old 1900s timber floorboards is, in my view a very fortunate Houzzer and would have a very difficult time trying to get anything today that remotely resembled those boards. I have a Queenslander from that era. All Queenslanders has tongue and groove Hoop PIne floors and they were nearly always covered in newspapers with "lino" ( made in England) over the top...so were well preserved. The advice I received about these untouched floorboards that had been seasoned naturally for many years prior to use was to initially "feed them" with a mix of kerosene and pale boiled linseed oil and then stain them if I wanted then give them a couple of sealant coats that would still allow them to breathe. I opted for just a kero and pale boiled linseed oil sprayover whenever they looked "thirsty" and I've used thick rugs to protect them from wear and tear. I've had them like this for 30 yrs or so and am very, very happy with my floors...and they are soft wood. Every couple of years I douse the floors with turpentine as this penetrates the timber and prevents termites, then continue on with the stain, kero and linseed oil mix...then get them buffed. That's just my story that may be or not a little helpful, I was born in Victoria so am familiar with the balck Japan satin that was used down the boards exposed each side of the hall runners....and the boards were the wider ones. Its a pity that multiple sandings compromise the tongue and groove..sometimes such floors need reinforcing from underneath. After acertaining that, maybe a light.soft timber "overfloor"rather than a hardwood would be the go although quite a bit of maintrnance for the first few years. You could stain it any colour you wanted. by getting a light to mid brown or teak stain and give it several coats allowing drying in between until you were satisfied with the colour. Its a good thing to keep in mind that timber flooring from that era was very well and naturally seasoned for years prior to being sold for use...the idea was to seel people timber that would last. I have put on a couple of decks here and am rather disappointed to see that the newer timbers are showing signs of wear and deterioration whilst the original timbers are still as unblemished and solid as the day they were used to build my old home. I think that was a very good lesson for me. All timbers today are kiln dried for expediency so, since they were not permitted to "age gracefully": and gently they are not naturally strong. If ever I do any more timber renos to this place I will be sourcing old timbers form places being demolished. These often cost more...but there's method in that madness! I'd say to anyone wanting their floors to stand the test of time...Buy old timber and treat it as it would have been treated of old. Should have some photos of these floors somewhere. I'll post them if I can

About your question about sourcing some of your own internal fittings. It is best you discuss this with the builder early on. Usually, the builder's contract will specify an allowance for particular fixtures. However, some may specify actual brand and model of fittings ie taps, toilets, sinks, etc in their quote, and they may or may not allow you to vary this. IF you are happy with those specified fixtures and you think the allowance amount is reasonable, then you can go with it. Otherwise, any changes or variances need to be discussed with builder, and it is very important this be discussed upfront and before any contract is signed. Some building contracts may also disallow some variances. In any event, carefully read the contract so you completely understand what you are agreeing to, and discuss any and all parts where you are not in agreement so these issues can be ironed out. Also, and this is my own experience and opinion, but I advise specifying in the contract the completion date AND if the build is not completed on time then what happens (consider that you may be paying interest on your mortgage, be financing a bridging mortgage, etc. and/or you may also have already sold your home and then have to pay rent until the build is finished). If you are in agreement with builder to source some of the internal fittings yourself, there are any number of suppliers and sources to investigate, and this might be a good way to keep your budget in check. There will be Houzzers who are experienced at this and can provide you with ideas. Just keep in mind that you will have to have all fittings READY and ON SITE when the tradesmen require them, otherwise you will be holding up the build and that is going to cost YOU money.

I would start with making a decision on the carport first. Start by talking to the council as you may not be able to do a double carport (and the single carport at your neighbours looks like a tight squeeze!) Also as Missmel said you should probably also make a decision whether to paint or not early on. If you are going to go with carport, paint, new awning and possibly porch windows you are getting into a whole new look so I would start talking a professional about the best way to design it. As an alternative to the porch enclosure could you get the front windows double glazed to reduce noise? If it was my place I think I would only be changing the awning, paint the fences, landscape, and maybe do a single carport if its really needed (plus the tiling etc that you mentioned). Some new fretwork might be nice too. To me the main thing to change is the bullnose, as you said its not original and it looks heavy and dominating. You will have to post some pics when done I will be really interested to see how this all turns out.