I know this is an old thread, but for the benefit of others who googled for a review and would like an opinion on the Parisi Ellisse toilet - here's my opinion after two to three years of use: Would I recommend - sorry, but no Loved the design and comfort of the toilet seat, but having used the toilet for a couple of years, this toilet has blocked on numerous occasions and partially blocked on even more. You'd think that by now flush design would have been well researched, and blockages would be rare, but we find blockages far too frequent. Maybe we just have too big a load. Of course, the trick to prevent blockage is to predict when the toilet may be getting full and to flush whilst mid-way between your number two, and /or be aware of how much toilet paper you might be using and take and extra flush. The other design issue I have is that the toilet seat cover and the top of the cistern is such that if you lean back, the seat cover raises the cistern cover slightly and when you stand up, the seat cover returns to its normal position and causes the cistern cover to drop back. This might be an installation issue, however, if so, then the tolerances for correct installation are very tight. Hope others find this feedback helpful.

I'm surprised to see someone recommending Villeroy and Boch toilets, and would love to see what they think after a couple of years. We were recommended this brand by our supplier (Hardware and General in Brookvale). It was a lot more expensive than the others, but we liked the design and we were happy to pay for something that we thought was better quality. We have had nothing but problems with it, and when we went back to the supplier, they contacted the company and they just said it was past the warranty period and they couldn't do anything. The rim is unglazed, so impossible to clean (the more you try to clean it, the dirtier it looks), there are a large number of cracks, and where the toilet seat connects is a dirt trap and difficult to clean. We have the original 1940s toilet from our home in the outside bathroom, and it looks immaculate. I would never recommend Villeroy and Boch - the product as well as the after sales service are terrible.

Such great ideas from everyone. The smaller the space, the more creative you need to be. A friend of mine has a tiny ensuite which she turned into a "wet room" and some of her Reno ideas are: Back-to-wall toilet (less space, easy to clean), In-wall (cavity) cabinet, Wall hung sink with a built in side shelf (with lovely chrome trap/plumbing). You do have to waterproof the ENTIRE room to have a wet room but don't need a shower door. She also tiled about 30cms outside the ensuite door (in the bedroom area) to save the bedroom floor from any water damage which turned out to be a great idea. Good luck with the Reno and I hope you post your "after" pics.

It's a little unconventional badobbs, but have you considered a toilet with in-built basin and tap - these are very sustainable (although not for everyone!) and are perfect for tight spaces. https://specify.caroma.com.au/products/toilet-suites/profile/profile-5-toilet-suite-deluxe-with-integrated-hand-basin.  To answer your question, usually you need min 800-900mm or so for a fixed panel for a shower, however normally walk-in open showers are located perpendicular to a room, so that splashes and wet floors are contained to one end. Think of when you drop the shower head and it sprays water everywhere! In your case I would advise selecting a well made frameless hinged door - so you can still have a walk-in effect but a bit more protection from water spraying out everywhere. Try Reece; https://www.reece.com.au/assets/brands/244000/custom-glass-brochure-v1.pdf The vanity depth is going to be the issue here, usually we advise min 800-850mm clearance (although can go down to 700 as per Dr Retro House Calls) and can see from the plan that with an 800 bath and 700 clearance you only have 250 depth for your vanity when it's near the bath. You could get a vanity made up at 250mm deep with a semi-inset deeper basin centrally - that way you can make the vanity a little longer but with a workable basin. https://specify.caroma.com.au/products/basins/luna/contemporary-luna-semi-recessed-basin-without-tap-landing Good Luck!